Next: RXR(1) Up: WFDB Applications Guide Previous: RDEDFANN(1)On This Page


rdsamp - read WFDB signal files


rdsamp -r record [ options ... ]


rdsamp reads signal files for the specified record and writes the samples as decimal numbers on the standard output. If no options are provided, rdsamp starts at the beginning of the record and prints all samples. By default, each line of output contains the sample number and samples from each signal, beginning with channel 0, separated by tabs.

Options include:

Produce output in CSV (comma-separated value) format (default: write output in tab-separated columns).
-f time
Begin at the specified time. By default, rdsamp starts at the beginning of the record.
Print a usage summary.
Read the signal files in high-resolution mode (default: standard mode). These modes are identical for ordinary records. For multifrequency records, the standard decimation of oversampled signals to the frame rate is suppressed in high-resolution mode (rather, all other signals are resampled at the highest sampling frequency).
-l interval
Limit the amount of output to the specified time interval (in standard time format; default: no limit). If both -l and -t are used, rdsamp stops at the earlier of the two limits.
Print times in seconds and milliseconds, and values in physical units. By default, rdsamp prints times in sample intervals and values in A/D units.
Same as -p, but yields higher precision in the sample values (8 decimal places rather than 3).
A single character can be attached to either -p or -P to choose the
format for the printed times in the first column of output. The choices are:
-pd (or -Pd)
Print time of day and date if known, as [hh:mm:ss DD/MM/YYYY]. The base time and date must appear in the header file for the record; otherwise, this format is equivalent to "e" format (below).
-pe (or -Pe)
Print the elapsed time from the beginning of the record, as hh:mm:ss.
-ph (or -Ph)
Print the elapsed time in hours.
-pm (or -Pm)
Print the elapsed time in minutes.
-ps (or -Ps)
Print the elapsed time in seconds. This is the default format when using -p or -P.
-pS (or -PS)
Print the elapsed time in sample intervals.
-s signal-list
Print only the signals named in the signal-list (one or more input signal numbers or names, separated by spaces; default: print all signals). This option may be used to re-order or duplicate signals.
-S signal
Search for the first valid sample of the specified signal (a signal name or number) at or following the time specified with -f (or the beginning of the record if the -f option is not present), and begin printing at that time.
-t time
Stop at the specified time. By default, rdsamp stops at the end of the record.
Print column headings (signal names on the first line, units on the second). The names of some signals are too wide to fit in the columns; such names are shortened by omitting the initial characters (since names of related signals often differ only at the end, this helps to make the columns identifiable). Names of units are shortened when necessary by omitting the final characters, since the initial characters are usually most important for distinguishing different units.
Produce output in WFDB-XML format (same as the CSV format produced using the -c option, but wrapped within an XML header and trailer). This format is recognized and parsed automatically by wrsamp.


It may be necessary to set and export the shell variable WFDB (see setwfdb(1) ).


This program is provided in the app directory of the WFDB Software Package. Run make in that directory to compile and install it if it have not been installed already.

The PhysioNet ATM ( provides web access to rdsamp (select Show samples as text from the Toolbox).

See Also

rdann(1) , setwfdb(1) , wrsamp(1)


George B. Moody (


Table of Contents

Up: WFDB Applications Guide

Please e-mail your comments and suggestions to, or post them to:

MIT Room E25-505A
77 Massachusetts Avenue
Cambridge, MA 02139 USA

Updated 28 May 2015